International, Interfine 2080
inkl. MwSt. zzgl. Versandkosten
Sofort versandfertig, Lieferzeit ca. 1-3 Werktage
- Artikel-Nr.: KB10201
Vorteile
- Professionelle Beratung
- Schnelle Lieferung
- Großes Sortiment
Interfine® 2080 is a high performance, two component, acrylic polysiloxane finish which affords extended lifetime to first maintenance when utilised as part of a high performance anti-corrosive system. Interfine 2080 offers superior gloss and colour retention and provides significantly improved resistance to yellowing and chalking when compared to typical conventional topcoats including catalysed acrylic and polyurethane finishes.
Intended Uses
Interfine 2080 is a tough, hard wearing finish coat for application over properly primed surfaces, which exhibits good abrasion resistance. Suitable for application by spray and roller, in both factory new construction and site maintenance application situations, and is an ideal solution where legislation prevents the use of isocyanates.
For use in those market sectors where high standards of cosmetic appearance and aesthetics are a key requirement. These include high performance steel constructions such as sports stadia, bridges, offshore platforms, FPSO vessels, tank farms, chemical and petrochemical plants, pulp and paper mills, and the power industry, in addition to general industrial and commercial steelwork where aesthetics are important.
| Colour | Wide range of colours available |
| Gloss Level | Gloss |
| Volume Solids | 60% ± 3% (depends on colour) |
| Typical Thickness | 50-75 microns (2-3 mils) dry equivalent to 83-125 microns (3.3-5 mils) wet |
| Theoretical Coverage | 12 m²/litre at 50 microns d.f.t and stated volume solids |
| Practical Coverage | Allow appropriate loss factors |
| Method of Application | Airless spray, Air spray, Brush, Roller |
| Regulatory Data | |
| Flash Point | Part A 27 °C Part B 44 °C Mixed 27 °C |
| Product Weight | 1.289 kg/l (10.8 lb/gal) |
| VOC | 2.85 lb/gal (342 g/lt) EPA Method 24 |
| Surface Temperature | 5 °C | 15 °C | 25 °C | 40 °C |
| Touch Dry | 4 hrs | 3 hrs | 2 hrs | 1 hr |
| Hard Dry | 1.5 d | 1 d | 18 hrs | 12 hrs |
| Overcoating Interval, Minimum | 1 d | 18 hrs | 12 hrs | 6 hrs |
Surface Preparation
All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000.
Primed Surfaces:
Interfine 2080 should always be applied over a recommended anti-corrosive coating scheme. The primer surface should be dry and free from all contamination and Interfine 2080 must be applied within the overcoating intervals specified (consult the relevant product data sheet).
Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) or SSPC-SP6, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch primed prior to the application of Interfine 2080.
| Mixing | Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base(Part A) and mix thoroughly with power agitator. |
| Mix Ratio | 5 part(s) : 1 part(s) by volume |
| Working Pot Life | 5 °C - 5 hrs 15 °C - 4 hrs 25 °C - 3 hrs 40 °C - 2 hrs |
| Airless Spray | Recommended Tip Range 0.28-0.43 mm (11-17 thou) Total output fluid pressure at spray tip not less than 155 kg/cm² (2204 p.s.i.) |
| Air Spray (Pressure Pot) | Recommended Gun: DeVilbiss MBC oder JGA Air Cap: 704 oder 765 Fluid Tip: E |
| Air Spray (Conventional) | Suitable Use suitable proprietary equipment |
| Brush | Suitable - Touch up and small areas only Typically 25-50 microns (1.0-2.0 mils) can be achieved |
| Roller | Suitable Typically 25-50 microns (1.0-2.0 mils) can be achieved |
| Thinner | International GTA007 Do not thin more than allowed by local environmental legislation |
| Cleaner | International GTA007 |
| Work Stoppages | Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA007. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. |
| Clean Up | Clean all equipment immediately after use with International GTA007. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation. |
Product Characteristics
Apply in good climatic conditions. The temperature of the surface to be coated must be at least 3°C (5°F) above the dew point.
When applying Interfine 2080 in confined spaces ensure adequate ventilation.
Level of sheen and surface finish are dependent on application method. Avoid using a mixture of application methods. Best results in terms of gloss and appearance will always be obtained with conventional air spray application.
For brush and roller application, and in some colours, two coats of Interfine 2080 may be required to give uniform coverage, especially when applying Interfine 2080 over dark undercoats, and when using certain lead free bright colours such as yellows and oranges. Best practice is to use a colour compatible intermediate or anticorrosive coating under the Interfine 2080.
Pot life times must not be exceeded even though the material may be still liquid and appear useable. It is good working practice that application should commence with full unopened units of material. Due to the moisture sensitivity with partially filled units of the curing agent component, there is a danger of reaction with atmospheric moisture which could adversely affect the performance of the final coating film.
Interfine 2080 will cure satisfactorily at relative humidities between 40% and 85%. Curing will be slower at lower humidities and faster at higher humidities.
Condensation occurring during or immediately after application may result in a matt finish and an inferior film.
Premature exposure to ponding water will cause colour change, especially in dark colours and at low temperatures.
When overcoating after weathering or ageing, ensure the coating is fully cleaned to remove all surface contamination such as oil, grease, salt crystals and traffic fumes, before application of a further coat of Interfine 2080.
This product is not recommended for use in continuous immersion conditions.
Where prolonged chemical or solvent splashing is likely to occur contact International Protective Coatings for information regarding suitability.
Note:
VOC values are typical and are provided for guidance purpose only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
Low molecular weight reactive additives, which will form part of the film during normal ambient cure conditions, will also affect VOC values determined using EPA Method 24.
Systems Compatibility
The following primers/intermediates are recommended for Interfine 2080:
• Intergard 343
• Intergard 361
• Intergard 787
• Intershield 300
Interfine 2080 should only be topcoated with itself, or Interfine 878
For other suitable primers/intermediates, consult International Protective Coatings.
Additional Information
Further information regarding industry standards, terms and abbreviations used in this data sheet can be found in the following documents available at www.international-pc.com.
Safety Precautions
This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and thecontainer(s), and should not be used without reference to the Material Safety Data Sheet (MSDS) which International Protective Coatings has provided to its customers.
All work involving the application and use of this product should be performed in compliance with all relevant national, Health, Safety & Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult International Protective Coatings for further advice.
| Volume (Liters) | Pack Sizes (Liters) | |
| Interfine® 2080 Part A | 16.67 | 20 |
| Interfine® 2080 Part B | 3.33 | 5 |
Storage
Lifetime at 25 °C
Minimum 12 Month(s)
Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Diese Angaben stammen aus dem offiziellen Technischen Datenblatt von dem Lackhersteller. Wir übernehmen keine Gewährleistung für die Richtigkeit / fehlerhafte Angaben.
Wir bitten Sie, sich ausschließlich ans Technische Datenblatt des Herstellers zu halten, welches Sie weiter unten als PDF-Download finden.
All information were taken out of the Technical Data Sheet provided by the manufacturer. We don't garantuee the correctness of any information.
Please adhere solely to the Technical Data Sheet provided by the manufacturer which you can download as a PDF-File further below.
